Suzuki Grandee of Wetar
+ General information
+ Maintenance and greasing
+ Heater, ventilation and conditioner
+ Steering
+ Suspension bracket
+ Wheels and tires
+ Forward driving shaft/bearing of a shaft. Oil epiploon
+ Driveshafts
+ Brake system
- Engines
+ Mechanical part of the G16 engine
- Mechanical part of the J20 engine
+ General description
- Routine maintenance
Compression check
Check of depression of the engine
Check of pressure of oil
Filtering element of the air filter
Case of butterfly valves and inlet collector
Collector of an exhaust system
Cover of a head of the cylinder
Oil pan and grid of the oil pump
Oil pump
Cover of a chain of synchronization
Second chain of synchronization and natyazhitel of a chain
First chain of synchronization and natyazhitel of a chain
Cam-shafts and regulators of a klapanny gap
Valves and head of the block of the cylinder
Pistons, piston rings, rods and cylinders
+ Assembly fittings of the engine
Special tool
Necessary service materials
Technical characteristics of the rotating moment of an inhaling
+ engine Cooling
+ Fuel system
+ ignition System
+ start System
+ release System
+ Transmissions
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. Immobilizer
+ Electric equipment
|
Oil pan and grid of the oil pump
Components
|
|
*1) Put hermetic 99000-31250 on the interfaced surfaces of an oil pan and the case pallet, having addressed to point of 1 procedure of installation. |
|
|
The rotating moment of an inhaling. |
Removal
|
|
- Take out oil щуп.
- Lift a vehicle and remove both lobbies of a wheel.
- Remove a box of the steering mechanism (4) from a vehicle.
- Remove the case of forward differential (1) with differential (2) from the chassis. Address to the Section Removal in Head Forward differential.
|
|
1 — the case of forward differential
2 — differential
3 — an oil pan |
- Merge engine oil, having opened a drain stopper.
- Remove an element of rigidity of transmission if that is available.
- Remove the bottom plate of the case of the coupling (a hydrotransformer case).
- Remove an oil pan and a grid of the oil pump (2) from a case.
|
|
1 — the oil pump
2 — a grid of the oil pump |
|
|
Cleaning
|
| |
- In an oil pan and screen of a grid of the oil pump.
|
| |
- Clean a condensed surface on an oil pan and a case. Remove oil, old hermetic and a dust from a condensed surface.
|
|
|
Installation
|
|
- To facilitate and provide oil pan installation, increase a gap between the engine and the vehicle case according to the following procedure.
- Remove a rack support.
- Disconnect an exhaust pipe from a collector of an exhaust system.
- Remove nuts of fastening of the engine (right and left).
- By means of the adaptation for engine lifting at installation, lift the engine on 2-3 cm (about 1 inch).
|
|
|
|
Do not lift the engine more than it is specified above. It can lead to engine or transmission damage. |
|
- Put hermetic on the interfaced surface of an oil pan (1) continuously. "And": hermetic 99000-31250.
|
|
"and" — 2 mm (0.08 inches)
«b» — 3 mm (0.12 inches) |
- Put ring-shaped consolidations (2), and establish a grid of the oil pump (3) on an oil pan (1). At first twirl grid bolts, and then an arm bolt the every rotating moment.
- The rotating moment of an inhaling:
- Bolt of a grid of the oil pump (and) — 11 N • m (1.1 kg-m, 8.0 pound on foot)
- Bolt of an arm of a grid of the oil pump (b) — 11 N • m (1.1 kg-m, 8.0 pound on foot)
|
|
- After installation of an oil pan (4) on the case pallet, insert tightening bolts and start to tighten at the center: turn a wrench outside, twisting on one bolt at a time. Fasten bolts and nuts the every rotating moment. The rotating moment of an inhaling: a bolt and an oil pan nut (c) — 11 N • m (1.1 kg-m, 8.0 pound on foot).
|
- Lower the engine and fasten nuts of fastening of the engine the every rotating moment, having addressed to the Section Engine in this Chapter.
|
|
- Insert new laying and a drain stopper (2) into an oil pan (1). Fasten a drain stopper the every rotating moment. The rotating moment of an inhaling: a drain stopper (and) — 50 N • m (5.5 kg-m, 36.5 pound on foot).
|
- Establish the bottom plate of the case of the coupling (a hydrotransformer case).
- Connect an exhaust pipe No. 1 to a collector of an exhaust system, having addressed to the Section the Collector of an exhaust system in this Chapter.
- Establish an element of rigidity of transmission on transmission and the cylinder block if that is available.
- Establish the case of forward differential according to procedure of the installation described in the Section Installation in Head Forward differential.
- Fill the case of forward differential with transmission oil, having addressed to Servicing in Head Forward differential.
- Establish a box of the steering mechanism in a vehicle, having addressed to the Section Carter of the power steering in Head power steering System.
- Establish oil щуп.
- Fill the engine with engine oil, having addressed to the Section Engine oil and the filter in Head Maintenance and greasing.
- Fill in in steering system with strengthening special liquid, having addressed to the Section power steering Liquid in Head power steering System.
- Check, whether leaks engine oil, oil of differential and steering liquid on each connection.
|
|
|
|
