Suzuki Grandee of Wetar
+ General information
- Maintenance and greasing
+ Service
- Maintenance
- Engine
Driving belt
GRM belt (only for G16 engines)
Klapanny gap (only for G16 engines)
Engine oil and filter
Cooling liquid
Exhaust system
+ ignition System
+ Fuel system
+ System of decrease in toxicity of an exhaust
+ Chassis and body
Final survey
Recommended liquids and lubricants
+ Heater, ventilation and conditioner
+ Steering
+ Suspension bracket
+ Wheels and tires
+ Forward driving shaft/bearing of a shaft. Oil epiploon
+ Driveshafts
+ Brake system
+ Engines
+ Fuel system
+ ignition System
+ start System
+ release System
+ Transmissions
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. Immobilizer
+ Electric equipment
|
Engine oil and filter
Replacement
|
|
-
Before oil plums, check the engine on leakages of oil. At any found signs of leak, before continuation of works eliminate the leak reason.
- Turn off a drain stopper and merge oil.
|
|
- After oil plum, will wipe dry a drain stopper. Twirl a drain stopper and tighten it according to the moment. Inhaling moment: drain stopper of engine oil (a): 50 N • m (5.0 kg-m).
|
|
|
- Turn off the oil filter, using a key for oil filters (the special tool). Special tool: (A) 09915-47330 (for the G16 and J20 engine).
|
|
|
Before installation of the new oil filter oil a sealing ring. For this purpose use engine oil. |
|
|
- Twist the new filter by hand till the moment while the sealing ring will not concern a landing surface.
|
- Tighten the filter on 3/4 turns from the moment of a contact with a landing surface, using a key for oil filters. Inhaling moment: oil filter (b): 14 N • m (1.4 kg-m) (standard).
|
|
1 — the oil filter
2 — a key for oil filters.
|
|
|
Correctly to tighten the oil filter, it is necessary to sustain precisely a position at which there is the first contact of a sealing ring to a landing surface. |
- Fill in oil to a maximum level (to FULL mark on щупе).
- The jellied opening is from above on a klapanny cover.
- It is recommended to use engine oil of grades of SG, SH, SJ or SL.
- Choose suitable viscosity according to the chart of characteristics of viscosity of engine oils [A].
Chart of characteristics of viscosity of engine oils
|
|
In temperature limits from - 20°С (-4°F) to 30°С (86°F) it is urgently recommended to use SAE 10 W-30 oil. |
|
|
G16 engine
|
J20 engine
|
|
Capacity of the oil pallet
|
About 4.0 liters
|
About 5.0 liters
|
|
Capacity of the oil filter
|
About 2.0 liters
|
|
Another
|
About 0.3 liters
|
About 0.4 liters
|
|
The general
|
About 4.5 liters
|
About 5.6 liters
|
|
|
Capacity of engine oil is precisely defined. Nevertheless, keep in mind that the actual amount of the oil necessary for replacement can differ slightly from tabular data, depending on various conditions (temperature, viscosity etc.) |
- Check the oil filter and a drain stopper on leaks.
-
Start the engine and let's to it work about three minutes. Muffle and wait 5 minutes before check of level of oil. Add oil if necessary to «FULL» mark on щупе.
|
|
The steps 1-11 described above, should be executed at the idle engine. For performance of a step 12 be convinced that there is a sufficient ventilation while the engine works. |
|
|
1 — the maximum mark (opening)
2 — the minimum mark (opening) |
|
|
|
|
