Suzuki Grand Vitara SQ416/SQ420/420WD

since 1998 of release

Repair and car operation



Suzuki Grandee of Wetar
+ General information
+ Maintenance and greasing
+ Heater, ventilation and conditioner
+ Steering
+ Suspension bracket
+ Wheels and tires
+ Forward driving shaft/bearing of a shaft. Oil epiploon
+ Driveshafts
+ Brake system
- Engines
   + Mechanical part of the G16 engine
   - Mechanical part of the J20 engine
      + General description
      - Routine maintenance
         Compression check
         Check of depression of the engine
         Check of pressure of oil
         Filtering element of the air filter
         Case of butterfly valves and inlet collector
         Collector of an exhaust system
         Cover of a head of the cylinder
         Oil pan and grid of the oil pump
         Oil pump
         Cover of a chain of synchronization
         Second chain of synchronization and natyazhitel of a chain
         First chain of synchronization and natyazhitel of a chain
         Cam-shafts and regulators of a klapanny gap
         Valves and head of the block of the cylinder
         Pistons, piston rings, rods and cylinders
      + Assembly fittings of the engine
      Special tool
      Necessary service materials
      Technical characteristics of the rotating moment of an inhaling
   + engine Cooling
+ Fuel system
+ ignition System
+ start System
+ release System
+ Transmissions
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. Immobilizer
+ Electric equipment





First chain of synchronization and natyazhitel of a chain

1 — the first chain of synchronization
2 — a directing wheel
3 — an axis of a directing wheel
4 — an asterisk of synchronization of the crankshaft
5 — a natyazhitel of a chain of synchronization
6 — a regulator of a natyazhitel of a chain of synchronization No. 1

7 — directing to a synchronization No. 1 chain
8 — a nut of a natyazhitel of a chain of synchronization
9 — the rasporny plug of a natyazhitel of a chain of synchronization
10 — a bolt of a regulator of a natyazhitel of a chain of synchronization No. 1
11 — a bolt of a directing chain of synchronization


The rotating moment of an inhaling.

Grease with engine oil sliding surfaces.

Removal

 PERFORMANCE ORDER

  1. Disconnect a negative cable from the accumulator.
  2. Merge engine oil.
  3. Merge antifreeze.
  4. Remove an oil pan and a grid of the oil pump, having addressed to the Section Oil pan and a grid of the oil pump in this Chapter.
  5. Uncover cylinder heads, having addressed to the Section the Cover of a head of the cylinder in this Chapter.
  6. Uncover synchronization chains, having addressed to the Section the Cover of a chain of synchronization in this Chapter.
  1. Repeatedly to establish a synchronization chain, turn the crankshaft so that marks of synchronization in a head of the cylinder and the block of the cylinder coincided with marks in asterisks.
  1. Remove the second chain of synchronization, having addressed to the Section the Second chain of synchronization and a natyazhitel of a chain in this Chapter.
  2. Remove directing to a synchronization No. 1 (1) chain.
  3. Remove a regulator of a tension of a chain of synchronization No. 1 (2).
  1. Remove a natyazhitel of a chain of synchronization (3).
  1. Remove directing wheel and the first chain of synchronization.
  2. Remove an asterisk of synchronization of the crankshaft.

Check

Directing to a synchronization No. 1 chain

Check a boot on wear or damage existence.

1 — directing to a synchronization No. 1 chain

Natyazhitel of a synchronization chain

Check a boot (1) about wear or damage.

Asterisk of synchronization of the crankshaft

Check an asterisk teeth about wear or damage.

Directing wheel

Check a teeth and the plug (1) asterisk about wear or damage.

First chain of synchronization

Check a synchronization chain on wear or damage existence.

Regulator of a tension of a chain of synchronization No. 1

Be convinced of that a latch (1) and a gear surface (2) are not damaged and the latch functions normally.

Installation

 PERFORMANCE ORDER

  1. Level a key of an asterisk of synchronization of a knee (1) with a mark of synchronization (2) on the cylinder block.
  1. Establish an asterisk of synchronization of the crankshaft (2). The mark of compliance looks towards a chain cover.
1 — the crankshaft
2 — the cylinder block
4 — a mark
  1. Oil the plug of a directing wheel (1).
  2. Establish an axis of an asterisk and directing wheel.
  1. Establish the first chain of synchronization (3), having leveled a dark blue plate (4) first chains of synchronization with a mark of compliance (2) on a directing wheel.
  1. Level a yellow plate (4) 1st chains of synchronization (3) with a mark of compliance (2) on an asterisk of synchronization of the crankshaft (1).
  1. Establish a natyazhitel of a chain of synchronization (1). The rotating moment of an inhaling: a nut of a natyazhitel of a chain of synchronization (and) — 25 N • m (2.5 kg-m, 18.5 pound on foot).
1 — a natyazhitel of a chain of synchronization
2 — the rasporny plug
  1. Having opened a latch (2) regulators of a tension No. 1 and having pressed a plunzher (1) into the case (3), fix it in this situation, having inserted a lock core (4) between a latch and the case.
  1. Establish a regulator of a tension of a chain of synchronization No. 1 (1). The rotating moment of an inhaling: a bolt of a natyazhitel of a chain of synchronization No. 1 (and) — 11 N • m (1.1 kg-m, 8.0 pound on foot).
  2. Pull out a lock core (3) of a regulator No. 1.
1 — a regulator of a tension of a chain of synchronization
2 — a natyazhitel of a chain of synchronization
3 — a lock core
  1. Establish directing to a synchronization No. 1 (1) chain. The rotating moment of an inhaling: a bolt of a directing chain of synchronization (and) — 9 N • m (0.9 kg-m, 6.5 pound on foot).
1 — directing to a synchronization chain
2 — bolts directing
  1. Check, that a dark blue plate (2) and a yellow plate (4) first chains of synchronization coincided with marks of compliance in asterisks.
1 — a mark of compliance in a directing wheel
2 — a mark of compliance in an asterisk of synchronization of a knee
3 — a label
4 — a yellow plate
  1. Establish the second chain of synchronization, having addressed to the Section the Second chain of synchronization and a natyazhitel of a chain in this Chapter.
  2. Establish a cover of a chain of synchronization, having addressed to the Section the Cover of a chain of synchronization in this Chapter.
  3. Establish a cover of a head of the cylinder, having addressed to the Section the Cover of a head of the cylinder in this Chapter.
  4. Establish an oil pan and a grid of the oil pump, having addressed to the Section Oil pan and a grid of the oil pump in this Chapter.
  5. Establish system of cooling and other parts.
  6. Fill in in cooling system antifreeze, in forward differential transmission oil, in the engine engine oil and in steering system with strengthening special liquid.
  7. Check, whether there is no leakage of antifreeze, liquid for system of a steering, leakage of exhaust gas and oil on each connection.