bridgestone .

Suzuki Grand Vitara SQ416/SQ420/420WD

since 1998 of release

Repair and car operation



Suzuki Grandee of Wetar
+ General information
+ Maintenance and greasing
+ Heater, ventilation and conditioner
+ Steering
+ Suspension bracket
+ Wheels and tires
+ Forward driving shaft/bearing of a shaft. Oil epiploon
+ Driveshafts
+ Brake system
- Engines
   + Mechanical part of the G16 engine
   - Mechanical part of the J20 engine
      + General description
      - Routine maintenance
         Compression check
         Check of depression of the engine
         Check of pressure of oil
         Filtering element of the air filter
         Case of butterfly valves and inlet collector
         Collector of an exhaust system
         Cover of a head of the cylinder
         Oil pan and grid of the oil pump
         Oil pump
         Cover of a chain of synchronization
         Second chain of synchronization and natyazhitel of a chain
         First chain of synchronization and natyazhitel of a chain
         Cam-shafts and regulators of a klapanny gap
         Valves and head of the block of the cylinder
         Pistons, piston rings, rods and cylinders
      + Assembly fittings of the engine
      Special tool
      Necessary service materials
      Technical characteristics of the rotating moment of an inhaling
   + engine Cooling
+ Fuel system
+ ignition System
+ start System
+ release System
+ Transmissions
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. Immobilizer
+ Electric equipment





Collector of an exhaust system

Components

The car is not equipped with catalytic converter

1 — a collector of an exhaust system
2 — laying of a collector of an exhaust system
3 — the sensor of heating of oxygen - 1

4 — the top cover of a collector of an exhaust system
5 — an element of rigidity of a collector of an exhaust system
6 — the coupling of the sensor of heating of oxygen – 2

The car is equipped with catalytic converter

1 — a collector of an exhaust system
2 — laying of a collector of an exhaust system
3 — the sensor of heating of oxygen - 1

4 — the top cover of a collector of an exhaust system
5 — an element of rigidity of a collector of an exhaust system
6 — the coupling of the sensor of heating of oxygen – 2


The rotating moment of an inhaling.

Not to use repeatedly.

In order to avoid a burn, do not serve an exhaust system, if it still hot. Service should be carried out after the system will be cooled.

Removal

 PERFORMANCE ORDER

  1. Disconnect a negative cable from the accumulator.
  1. Disconnect the coupling of the sensor of heating of oxygen-1 (1) and disconnect it from its nest.
  1. Remove the top cover (2) collectors of an exhaust system.
  1. Remove an element of rigidity of a collector of an exhaust system (1) if that is available.
  1. Remove bolts and nuts of a pipe of No. of 1 exhaust system and a bolt of an arm of an exhaust pipe (if that is available).
1 — an exhaust pipe No. 1
  1. Remove a collector of an exhaust system (1) and its laying (2) from a cylinder head.

Installation

 PERFORMANCE ORDER

  1. Put new laying (1) on a cylinder head.
  1. Establish a collector of an exhaust system.
  1. Establish a ring sealant and an exhaust pipe No. 1 (1) to a collector of an exhaust system. Before establishing a ring sealant, check it about damage or wear, and if necessary replace. Use new lock-nuts if they are worn-out. Fasten pipe fixture the every rotating moment. The rotating moment of an inhaling: a bolt or a nut of an exhaust pipe No. 1 (and) — 50 N • m (5.0 kg-m, 36.5 pounds on foot).
  1. Establish an element of rigidity of a collector of an exhaust system (1) if that is available. Fasten a bolt and a nut of an element of rigidity of a collector of an exhaust system to the specified rotating moment.
  1. Establish the top cover (2) on a collector of an exhaust system.
  1. Connect the coupling (1) sensor of heating of oxygen - 1 and reliably insert the coupling into an arm.
  1. Connect a negative cable to the accumulator.
  2. Check, whether there is no leakage of exhaust gas from an exhaust system.