Suzuki Grandee of Wetar
+ General information
+ Maintenance and greasing
+ Heater, ventilation and conditioner
+ Steering
+ Suspension bracket
+ Wheels and tires
+ Forward driving shaft/bearing of a shaft. Oil epiploon
+ Driveshafts
- Brake system
+ Brakes
+ Brake highway/hose / main cylinder of a brake
+ Forward brakes
- Parking and back brake
+ General description
- Diagnostics
Check and adjustment
Vehicle service
Cable of the parking brake
Brake drum
Brake shoe
Brake cylinder
Back plate of a brake
+ Anti-blocking brake system (ABS)
+ Engines
+ Fuel system
+ ignition System
+ start System
+ release System
+ Transmissions
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. Immobilizer
+ Electric equipment
|
Brake shoe
|
|
- If the slip is worn-out beyond the limit, replace a boot.
- If one of brake slips is worn-out to a limit, it is necessary to replace all slips at the same time.
- Thickness of a brake shoe of "a":
- standard: 6.5 mm (0.24 inches)
- wear limit: 3.0 mm (0.12 inches)
|
|
Never polish a slip with an emery paper. If to polish it with an emery paper, rigid particles from an emery paper remain on a slip and can damage a drum. When it is necessary to correct a slip, replace it with the new. |
|
|
Installation
|
|
See. The note at the beginning of this Chapter. |
|
|
- Before installation of a brake drum, check external diameter of a brake shoe (3). If it does not correspond to the value given below, adjust it according to specifications, having turned a regulator (4). External diameter of a brake shoe: "a" — 219.4 - 219.7 mm (8.638 - 8.650 inches).
|
|
1 — the lock lever
2 — a regulator pin |
- Establish a brake drum, having convinced that the internal part of a brake drum and brake shoes are free from dirt and oil.
- On termination of works, press the brake lever with effort about 30 kg (66 pounds) from three to ten times to receive a necessary gap between a drum and a boot. Adjust a cable of the parking brake (for adjustment, address to the Section Check and adjustment of the parking brake in Head Brake system).
- Establish a back central console box.
|
|
Establish a wheel and tighten wheel nuts with the specified torque of an inhaling. Inhaling torque: wheel nut (b): 100 N • m (10.0 kg-m, 72.5 pounds foots). |
- Check and be convinced that the brake drum does not jam and brakes work correctly. Then remove a vehicle from the lift and execute brake check (a foot brake and the parking brake).
|
|
Brake shoe
Removal
|
|
- Execute item of 1-5 procedure of removal of the Section the Brake drum.
|
|
Be especially careful, establishing a returnable spring of a brake shoe. The wrong installation can lead to that the spring will come off and can become the trauma reason. |
|
|
- Remove the springs pressing a boot (1), having unbent the pins pressing a boot (2).
|
- Remove the top returnable spring (4), assembly of a regulator (3), the lever of a regulator (5), a spring of the lever of a regulator (6), a rack spring (8), and a jay (7).
- Remove brake shoes and the bottom returnable spring of a boot (9).
- Remove brake shoes and disconnect a cable of the parking brake (2) from the lever of a block of the parking brake (1).
|
|
3 — a branch pipe of a brake cable |
|
|
- Remove the lever of a block of the parking brake (2) and the holder (1) from a brake shoe (3).
|
|
|
Survey
Lever of a lay boot
|
|
Examine the lever of a brake shoe and check, whether movement of rather brake shoe is free. If it is faulty, correct or replace.
|
Regulator assembly
|
|
Check a carving or a ratchet of a rack and a regulator, whether there is no wear, jamming and corrosion.
|
Springs
|
|
- Examine are not damaged and whether weakened springs.
|
|
- Examine each part with an arrow, whether there is no rust. If there are malfunctions, replace.
|
|
|
Brake shoe
Address to subsection Section Survey the Brake drum.
Installation
|
|
- Collect parts as it should be, the return to an order at removal.
|
|
1 — the bottom returnable spring
2 — the bottom rack |
|
|
- Establish the springs holding a boot (1) having pressed down them on a place and turning clamping pins (2).
|
- Establish assembly of a regulator (3) and the top returnable spring of a boot (4).
- Establish the lever of a regulator (5), a spring of the lever of a regulator (6), assembly of a rack (7) and a rack spring (8).
- Establish the bottom returnable spring of a boot (9).
- Then address to the Section the Brake drum.
|
|
|
|
