The device, service, Suzuki Grand Vitara SQ416/SQ420/420WD repair - a wheel Nave (including the wheel bearing)//Suzuki the Grandee of Wetar since 1998 /

Suzuki Grand Vitara SQ416/SQ420/420WD

since 1998 of release

Repair and car operation



Suzuki Grandee of Wetar
+ General information
+ Maintenance and greasing
+ Heater, ventilation and conditioner
+ Steering
- Suspension bracket
   - Forward suspension bracket
      General description
      + Diagnostics
      - Service out of a workshop
         Stabilizer of the cross-section stability/plug
         Shock-absorber rack
         Cylindrical spring
         Limiter of a dynamic course of a suspension bracket / Rubber nest of a spring
         Wheel nave (including the wheel bearing)
         Rotation hinge/axis
         Suspension bracket/plug lever
   + Back suspension bracket
+ Wheels and tires
+ Forward driving shaft/bearing of a shaft. Oil epiploon
+ Driveshafts
+ Brake system
+ Engines
+ Fuel system
+ ignition System
+ start System
+ release System
+ Transmissions
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. Immobilizer
+ Electric equipment


delicious pizza v Bratislave, ra?a d?bravka lama?



Wheel nave (including the wheel bearing)

Removal

 PERFORMANCE ORDER

  1. Lift the car and remove a wheel.
  1. Remove a flange of a drive of an axis of a shaft (1) (at the all-wheel drive car) or a cap of a nave of a wheel (at the car with a drive on two wheels).
  1. If there is a system of anti-blocking of brakes (ABS), remove the sensor of speed of a wheel from a fist and the fastening plug from a rack.
  2. Remove a bolt of a support of a disk brake and leave a support to hang.

Hang up the removed support of a disk brake on a wire hook or something similar that the brake hose strongly was not bent and it was not overwound or it was not pulled out. Do not press a brake pedal when brake shoes are removed.


  1. Remove a brake disk.

If the brake disk does not act in film hands, use 8-millimetric bolts.


  1. Remove a lock washer of the bearing of a forward wheel (1), having weakened 4 bolts (2).
  1. By means of the special tool remove a lock-nut of the bearing of a forward wheel. Special tool: (A): 09951-16050.
  1. Remove a washer of the bearing of a forward wheel.
  2. Hands remove a wheel nave.

If it is not possible to remove a wheel nave manually, use special tools.

Special tool

(B) — 09943-35512
(C) — 09942-15510


If at removal of a nave of a wheel the internal holder of the bearing of a wheel remains on an axis of a fist of a wheel that means breakage of the bearing of a wheel, replace a wheel nave (together with the wheel bearing).

  1. Remove a sensor (1) rotor from a nave of a wheel (2) (if there is a system of anti-blocking of brakes of ABS).
  • Gradually and evenly extend a sensor rotor from a wheel nave.
  • Do not use the removed rotor of the sensor repeatedly. At installation put a new rotor of the sensor.
  1. Remove from a nave nave bolts.
1 — a sensor rotor
2 — a wheel nave
3 — a vice
4 — the flat end of draft

Installation

1 — a lock washer
2 — a bolt
3 — a bearing lock-nut
4 — a washer of the bearing of a wheel
5 — a wheel nave
6 — a bolt

 PERFORMANCE ORDER

  1. Insert a new pin into a nave opening. Slowly it повращайте to be convinced that crenulate connections coincide with the connections made an initial bolt.
1 — an oil hydraulic press
2 — a nave bolt
  1. Establish a new rotor of the sensor (1) by means of the special tool (if there is a system of anti-blocking of brakes of ABS).
    • Special tool
      • (A): 09952-86510
      • (B): 09924-74510

Be attentive not to insert a nave of a wheel (2) on a diagonal.


The provision of a rotor of the sensor of speed of a wheel (1) at installation.
Rough size "a": 4.9 ± 0.1 mm (0.19 ± 0.004 inch).
3 — a hydraulic press

  1. Fingers establish a nave of a wheel (1) on a spindle supporting an internal holder (3).

Do not beat on a wheel nave a hammer or something heavy. It is so possible to break it.


If it is impossible to establish a wheel nave manually, (that means that the internal holder is not leveled), remove a nave of a wheel and establish it again.


1 — a wheel nave
2 — a wheel spindle
3 — an internal holder
  1. Establish a washer of the bearing of a wheel, and then a lock-nut of the bearing of a wheel.
  1. Turning a hand a wheel nave, tighten a lock-nut of the bearing of a wheel to the specified value of the moment of an inhaling. Special tool: (A) 09951-16050. Inhaling moment: a lock-nut of the bearing of a wheel (a) — 216 N • m (21.6 kg-m, 157 pounds foots).
  1. Lock washer (1) block a bearing lock-nut. If the opening of a blocking bolt is not leveled with an opening in a lock-nut, turn a lock-nut in the tightening direction until they will not be leveled. Inhaling moment: a blocking bolt (b) — 1.5 N • m (0.15 kg-m, 1.1 pounds foots).
  1. For the all-wheel drive car use plastic lithium greasing for a washer of a shaft of a forward drive and an external axis of a fist of a forward wheel. “A”: greasing 99000-25010.
  1. For the all-wheel drive car at installation of a lock ring (1) on a shaft of a drive use a boltovy opening in a drive shaft to pull out it and to turn in big diameter (2) rings to the right.
  1. At cars with system of anti-blocking of brakes of ABS check, that no alien material stuck to the sensor and a rotor. Establish the sensor of speed of a wheel (1) and the plug of its fastening.
    • Inhaling moment:
      • bolt of the plug of fastening (a): 10 N • m (1.0 kg-m, 7.5 pounds foots)
      • bolt of the sensor (b): 23 N • m (2.3 kg-m, 17.0 pounds foots)

  • At installation of the sensor of speed of a forward wheel (1) do not pull and do not overwind excessively connecting wires.
  • Reliably attach a sealing ring to an internal wing.

  1. Check, that there was no gap between the sensor and a fist.
  1. Establish a brake disk and a support of a disk brake. Inhaling moment: a bolt of a support of a disk brake (e) — 85 N • m (8.5 kg-m, 61.5 pounds foots).
  1. Put hermetic and establish a flange of a drive of an axis of a shaft or a cap of a nave of a wheel.

For the all-wheel drive car

  1. Put hermetic on an adjoining surface of a flange of a drive of an axis of a shaft (1), then establish a flange of a drive of an axis of a shaft and tighten a flange bolt (2) to the specified value of the moment of an inhaling.
  • Inhaling moment:
    • bolt of a flange of a drive (a): 50 N • m (5.0 kg-m, 36.5 pounds foots)
    • “A”: hermetic 99000-31090

For the car with a drive on two wheels

  1. Remove greasing, old hermetic and dirt from adjoining surfaces of a cap of a nave of a wheel (3) and naves (4), on the cleared surface of a cap of a nave evenly put water-proof hermetic "A" and establish a cap on a nave. “A”: hermetic 99000-31090.
  1. Establish a wheel. Inhaling moment: nut of a wheel (a): 100 N • m (10.0 kg-m, 72.5 pounds foots).
  1. For cars with system of anti-blocking of brakes of ABS, carry out a verifying trip as it is described in Head Anti-blocking brake system (ABS), (The table of diagnostics of malfunctions of ABS).