Suzuki Grandee of Wetar
+ General information
+ Maintenance and greasing
+ Heater, ventilation and conditioner
+ Steering
- Suspension bracket
- Forward suspension bracket
General description
+ Diagnostics
- Service out of a workshop
Stabilizer of the cross-section stability/plug
Shock-absorber rack
Cylindrical spring
Limiter of a dynamic course of a suspension bracket / Rubber nest of a spring
Wheel nave (including the wheel bearing)
Rotation hinge/axis
Suspension bracket/plug lever
+ Back suspension bracket
+ Wheels and tires
+ Forward driving shaft/bearing of a shaft. Oil epiploon
+ Driveshafts
+ Brake system
+ Engines
+ Fuel system
+ ignition System
+ start System
+ release System
+ Transmissions
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. Immobilizer
+ Electric equipment
|
Cylindrical spring
Removal
|
|
- Lift the car that the forward suspension bracket freely hung.
- Remove wheels.
|
|
- Remove a flange of a drive of an axis of a shaft (at the all-wheel drive car).
|
|
|
- Remove a spring ring of a shaft of a forward drive (1) (at the all-wheel drive car).
|
|
|
- Remove bolts of a support of a disk brake and hang up a support on a wire hook (1).
|
|
|
Hang up the removed support of a disk brake on a wire hook that the brake hose was not bent and it was not overwound and it was not stretched. Do not press a brake pedal when brake shoes are removed. |
|
|
- If there is a system of anti-blocking of brakes (ABS), remove a bolt of the plug of a wire (2) and remove the sensor of speed of a forward wheel (1) from a pin.
|
|
|
- Do not pull a wire when remove the sensor of speed of a forward wheel (1).
- Do not damage a surface of the sensor of speed of a forward wheel (1) and track, that the dust did not get to its opening for installation, dirt, etc.
|
|
|
If it is impossible to remove a disk hands, use 8-millimetric bolts. |
- Remove a bar of the stabilizer of cross-section stability as it is described in this Chapter in the Section the Stabilizer of the cross-section stability/plug, (Removal point).
|
|
- Disconnect a tip of steering draft from a rotary pin by means of a stripper.
|
|
|
- Jack prop up the bottom lever.
|
|
|
- Remove bolts of a bracket of a rack.
|
- Remove a hairpin nut with a spherical tip.
|
|
- By means of a stripper disconnect a rotary pin from a hairpin with a spherical tip.
|
- Lowering a jack, remove a rotary pin and a wheel nave.
|
|
- Remove a cylindrical spring (1).
|
|
|
Installation
|
|
- For installation of a cylindrical spring execute in return sequence of manipulation on its removal.
|
|
The top and bottom diameters of a cylindrical spring are not identical. The end with big diameter put down, and the free end establish in a nest of a spring (1). |
- At a tightening of all boltovy connections observe the specified values of the moment of an inhaling.
- As to a hairpin nut with a spherical tip, do not forget to insert шплинт and to bend it after a nut tightening.
- Tighten a nut of a tip of steering draft a hairpin with spherical tips up that the hairpin did not rotate.
For the all-wheel drive car
|
|
a. For a washer of a shaft of a forward drive and an external axis of a fist of a forward wheel use lithium plastic greasing. “A”: cмазка 99000-25010.
|
For the all-wheel drive car
|
|
b. At installation of a cutting lock ring (1) on a shaft of a drive use a boltovy opening in a drive shaft to pull out it and to turn in big diameter (2) rings to the right.
|
For the all-wheel drive car
|
|
c. At installation of a flange of a drive of an axis of a shaft (1) on a nave of a wheel put hermetic on an adjoining surface of a flange of a drive of an axis of a shaft and tighten a bolt of a flange (2) to the specified value of the moment of an inhaling. “A”: hermetic 99000-31090. Inhaling moment: bolt of a flange of an axis of a shaft (a): 50 N • m (5.0 kg-m, 36.5 pounds foots).
|
|
|
- Check, that no alien material stuck to the sensor and a rotor. Establish the sensor of speed of a wheel (1) and the plug of its fastening.
- Inhaling moment:
- bolt of the plug of fastening (a): 10 N • m (1.0 kg-m, 7.5 pounds foots)
- bolt of the sensor of speed (b): 23 N • m (2.3 kg-m, 17.0 pounds foots)
|
|
|
At installation of the sensor of speed of a forward wheel do not pull and do not overwind excessively connecting wires. Reliably attach a sealing ring to an internal wing. |
- Check, that there was no gap between the sensor and a fist.
|
|
|
|
