Suzuki Grandee of Wetar
+ General information
+ Maintenance and greasing
+ Heater, ventilation and conditioner
+ Steering
- Suspension bracket
- Forward suspension bracket
General description
+ Diagnostics
- Service out of a workshop
Stabilizer of the cross-section stability/plug
Shock-absorber rack
Cylindrical spring
Limiter of a dynamic course of a suspension bracket / Rubber nest of a spring
Wheel nave (including the wheel bearing)
Rotation hinge/axis
Suspension bracket/plug lever
+ Back suspension bracket
+ Wheels and tires
+ Forward driving shaft/bearing of a shaft. Oil epiploon
+ Driveshafts
+ Brake system
+ Engines
+ Fuel system
+ ignition System
+ start System
+ release System
+ Transmissions
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. Immobilizer
+ Electric equipment
|
Suspension bracket/plug lever
Removal
|
|
- Remove a cylindrical spring. See in this Chapter the Section the Cylindrical spring.
- Remove bolts and nuts of the lever of a suspension bracket. Then remove the suspension bracket lever.
- Carefully, not to damage a face surface of the lever of a suspension bracket, cut off a flange part of the plug of the lever of a suspension bracket (rubber and steel). Size "A": about 6 mm (0.236 inches).
|
|
1 — a cut-off flange
2 — external diameter of the plug |
|
|
- Put the lever of a suspension bracket and the special tool on a hydraulic press. Combine a cut-off flange of the lever of a suspension bracket with the welded part (1) special tool, and the party of connection with the suspension bracket lever with a step part (2) of the special tool. The special tool (A) — 09951-46020.
|
|
|
With extra care pull out the plug of the lever of a suspension bracket to press it vertically. Otherwise it is possible to be traumatized. |
|
|
- Remove the forward plug, having pulled out it by means of a hydraulic press (1) and the special tool.
- Special tool:
- (A): 09951-46020.
- (B): 09924-74510
- (C): 09951-16060
|
|
|
- Remove the back plug, having pulled out it by means of a hydraulic press (1) and the special tool.
- Special tool:
- (A): 09951-46020
- (D): 09913-80112
- (E): 09925-58210
|
|
|
Installation
Forward plug
By means of the special tool, press the forward plug (2) while its flange will not concern edge of the case of the lever of a suspension bracket.
- Special tool
- (C): 09951-16060
- (F): 09913-85210
|
|
Cave-in of the plug can be facilitated if to process an internal surface of the case of the lever of a suspension bracket soap water or oil with additives. |
|
|
1 — a hydraulic press
And — the flange of the plug concerns edge of the case |
Back plug
|
|
- By means of the special tool, press the back plug (2) while its flange will not concern edge of the case of the lever of a suspension bracket.
- Special tool
- (E): 09925-58210
- (F): 09913-85210
|
|
Cave-in of the plug can be facilitated if to process an internal surface of the case of the lever of a suspension bracket soap water or oil with additives. |
|
|
1 — a hydraulic press
2 — the back plug
And — the flange of the plug concerns edge of the case |
- Establish the suspension bracket lever on the chassis.
- Lower the car in situation without loading and tighten a nut of the lever of a suspension bracket to the specified value of the moment of an inhaling.
|
|
|
|
In model with the H27 engine do not use repeatedly back nut of the forward lever of a suspension bracket (1). |
|
- Inhaling moment:
- Forward nut of the lever of a suspension bracket (a): 85 N • m (8.5 kg-m, 61.5 pounds foots)
- Back nut of the lever of a suspension bracket (b): 126 N • m (12.6 kg-m, 91.0 pound foot)
- Further installation is similar to installation of a cylindrical spring. See in this Chapter the Section the Cylindrical spring.
|
|
|
|
