- For installation of a fist, an oil epiploon of an axis of a fist of a wheel and the bearing of a shaft of a drive (2) execute in return sequence of manipulation on removal, paying attention to the following.
All-wheel drive car
|
|
1 — an axis of a fist of a wheel
3 — a persistent washer of a shaft of a forward drive (type "C" or "D")
4 — an internal oil epiploon
6 — an oil epiploon of a shaft of a drive
With — flat type
D — flange type (for a cabriolet) |
The car with a drive on two wheels
|
|
1 — an axis of a fist of a wheel
5 — a fist cap
|
For the all-wheel drive car
- By means of the special tool establish the bearing of a shaft of a drive (1).
- Special tool:
- (A): 09913-76010 — a persistent washer of a shaft of a drive of type C
- (A): 09913-80112 — a persistent washer of a shaft of a drive of type D
- Persistent washer of a shaft of a drive of type A
- Size "a": 0–1 mm (0 – 0.04 inches)
- Persistent washer of a shaft of a drive of type B
- Size "a": 1.75-2.50 mm (0.069 – 0.098 inches)
- At installation of an axis of a fist of a wheel on a fist, process adjoining surfaces hermetic. “A”: hermetic 99000-31110.
For the all-wheel drive car
|
|
- Besides, fill a flute in an axis of a fist of a wheel in about ten grams of plastic lithium greasing. “B”: greasing 99000-25010.
|
|
|
- Tighten a nut of an axis of a fist of a wheel to the specified value of the moment of an inhaling. Inhaling moment: nut of an axis of a fist of a wheel (a): 50 N • m (5.0 kg-m, 36.5 pounds foots).
|
For the all-wheel drive car
- In pressing establish an internal oil epiploon.
|
|
- By means of the special tool enter inside an internal oil epiploon while its end will not concern a step surface of a fist.
- Special tool:
- (B): 09944-66010
- (C): 09924-74510
|
For the all-wheel drive car
- Put plastic lithium greasing on an edge of an oil epiploon and in his cavity, having filled it more, than for 60 %.
- Put lithium plastic greasing "A" on a shaft of a drive (2). “A”: greasing 99000-25010.
- Pressing establish a persistent washer of a shaft of a forward drive (3) on a shaft of a drive (2) if it was removed (for a persistent nut of a shaft of a drive of type B). Put lithium plastic greasing "A" on a persistent washer of a shaft of a drive. “A”: greasing 99000-25010.
- Put lithium plastic greasing "A" and establish a persistent washer of a shaft of a forward drive (3) rounded off by the party to the central party (for a persistent washer of a shaft of a drive of type A). “A”: greasing 99000-25010.
|
|
Type C — a flat washer
Type D — a razvaltsovanny washer |
For the car with a drive on two wheels
- Remove greasing, old hermetic and dirt from adjoining surfaces of a cap of a fist (2) and a fist (1), on a pure surface of a cap evenly put water-proof hermetic and establish a cap on a fist. “B”: hermetic 99000-31090.
|
|
1 — a fist
2 — a fist cap
3 — a wheel spindle |
|
|
- Tighten a nut of the lever of a hairpin with a spherical tip. For this purpose take a new nut and tighten it to the specified value of the moment of an inhaling. Inhaling moment: a hairpin nut with a spherical tip (a): 60 N • m (6.0 kg-m, 43.5 pounds foots).
|
For the car with a drive on two wheels
|
|
- Put water-proof hermetic on an adjoining surface of a nave of a wheel (1) and establish a cap of a nave (2) on a wheel nave. “A”: hermetic 99000-31090.
|
For the all-wheel drive car
|
|
- At installation of a flange of a drive of the bridge (1) on a wheel nave, put hermetic on an adjoining surface of a flange of a drive of the bridge (1). “A”: hermetic 99000-31090. Inhaling moment: bolt of a flange of a drive (a): 50 N • m (5.0 kg-m, 36.5 pounds foots).
|
- For installation of a nave of a wheel see in this Chapter Undressed a wheel Nave (including the wheel bearing).
|
|
- Connect a tip of steering draft to a fist and tighten a new nut of a tip of steering draft. Inhaling moment: nut of a tip of steering draft (a): 40 N • m (4.0 kg-m, 29.0 pounds foots).
|
|
