Suzuki Grandee of Wetar
+ General information
+ Maintenance and greasing
+ Heater, ventilation and conditioner
+ Steering
+ Suspension bracket
+ Wheels and tires
+ Forward driving shaft/bearing of a shaft. Oil epiploon
+ Driveshafts
+ Brake system
+ Engines
+ Fuel system
+ ignition System
+ start System
+ release System
+ Transmissions
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. Immobilizer
- Electric equipment
+ body Electric equipment
+ lighting System
- Electric equipment system
+ General description
+ Diagnostics
+ the Works made on the car
- Major maintenance
- Generator
Removal
Installation
Dismantling [Type 60 A]
Dismantling [Type 70 A and 80 A]
Survey [Type 60 A]
Survey [Type 70 A and 80 A]
Replacement of brushes
Assembly [Type 60 A]
Assembly [Type 70 A and 80 A]
+ Specifications
Inhaling moments
+ Tools/information for drivers
|
Assembly [Type 70 A and 80 A]
|
|
- If bearing of a casing it is removed, establish it.
- Check that it rotates smoothly.
|
|
1 — the casing bearing
2 — a rotor
3 — a bearing cover |
- If the stator is removed, establish a stator and tighten carving hairpins.
- If the bearing of a drive is removed, establish it.
- Check that it rotates smoothly.
- Inhaling torque
- (a): 8.8 N • m (0.88 kg-m, 6.5 pounds foots)
- (b): 2.6 N • m (0.26 kg-m, 2.0 pounds foots)
|
|
1 — a carving hairpin
2 — a holding plate
3 — the drive bearing
4 — a stator |
- Place a drive frame on a pulley, and establish a rotor on a frame.
- Establish a back frame on a driving frame.
- Tighten 4 nuts the every rotating moment. Torque of an inhaling (a): 4.5 N • m (0.45 kg-m, 3.5 pounds foots).
|
|
1 — a back frame
2 — a driving frame |
- Establish a pulley and tighten a pulley nut, holding a shaft a six-sided wrench the every moment of an inhaling. Torque of an inhaling (a): 111 N • m (11.1 kg-m, 80.5 pounds foots).
|
|
1 — a pulley
2 — a six-sided key
3 — a cranked wrench |
- Establish 4 rubber insulators.
- Establish the rectifier.
- Inhaling torque
- (a): 2.0 N • m (0.2 kg-m, 1.5 pounds foots)
- (b): 3.9 N • m (0.39 kg-m, 3.0 pounds foots)
|
|
At rectifier installation, check and be convinced that between contacts the stator and blades of the cooling fan is a sufficient gap. |
|
|
- Establish a cover of a shchetkoderzhatel on a shchetkoderzhatel.
|
- Place IC a regulator together with a shchetkoderzhatel horizontally on a back frame.
- Establish 5 screws while the gap between a shchetkoderzhatel and a connector will not be about 1 mm (0.04 inches). Torque of an inhaling (a): 2.0 N • m (0.2 kg-m, 1.5 pounds foots).
|
|
1 — an IC regulator
2 — a shchetkoderzhatel
3 — a back frame |
- Establish a back cover and a terminal plate.
- Inhaling torque
- (a): 4.5 N • m (0.45 kg-m, 3.5 pounds foots)
- (b): 3.8 N • m (0.38 kg-m, 3.0 pounds foots) (only type 80 A)
- Establish an insulator and tighten an internal nut of the plug "B" the every moment. Torque of an inhaling (c): 4.2 N • m (0.42 kg-m, 3.0 pounds foots).
|
|
1 — a back cover
2 — an insulator
3 — an internal nut of the plug "B"
4 — a terminal plate (only type 85 A) |
|
|
- Be convinced that the rotor rotates smoothly.
|
|
|
|
|
