Suzuki Grandee of Wetar
+ General information
+ Maintenance and greasing
+ Heater, ventilation and conditioner
+ Steering
+ Suspension bracket
+ Wheels and tires
+ Forward driving shaft/bearing of a shaft. Oil epiploon
+ Driveshafts
+ Brake system
+ Engines
+ Fuel system
+ ignition System
+ start System
+ release System
+ Transmissions
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. Immobilizer
- Electric equipment
+ body Electric equipment
+ lighting System
- Electric equipment system
+ General description
+ Diagnostics
+ the Works made on the car
- Major maintenance
- Generator
Removal
Installation
Dismantling [Type 60 A]
Dismantling [Type 70 A and 80 A]
Survey [Type 60 A]
Survey [Type 70 A and 80 A]
Replacement of brushes
Assembly [Type 60 A]
Assembly [Type 70 A and 80 A]
+ Specifications
Inhaling moments
+ Tools/information for drivers
|
Survey [Type 70 A and 80 A]
Rotor
|
|
|
|
- Using an ohmmeter, check electroconductivity between contact rings of a rotor. If there is no electroconductivity, replace a rotor. Standard resistance: about 2.9.
|
|
|
- Using an ohmmeter, check, whether there is no electroconductivity between contact rings and a rotor. If there is an electroconductivity, replace a rotor.
|
- Check contact rings, whether there is no roughness or a deposit. If they rough or are a deposit, replace a rotor.
|
|
- Using a calliper with noniusy, measure diameter of a contact ring.
- standard diameter: 14.2-14.4 mm (0.557 - 0.567 inches)
- minimum diameter: 12.8 mm (0.504 inches)
|
- If diameter less minimum, replace a rotor.
|
|
Stator
|
|
|
|
- Using an ohmmeter, check electroconductivity of all contacts. If there is no electroconductivity, replace a stator.
|
|
|
- Using an ohmmeter, check, whether there is no electroconductivity between contacts of a stator and the stator core. If there is an electroconductivity, replace a stator.
|
|
|
Brush and shchetkoderzhatel
|
|
Check each brush on wear, having measured its length, as shown. If the brush is worn-out to a limit, replace a brush. Address to the Section Replacement of brushes in this Chapter.
- Length of an open part of a brush of "a":
- standard: 10.5 mm (0.413 inches)
- limit: 4.5 mm (0.351 inches)
|
Rectifier
Positive rectifier
|
|
- Using an ohmmeter, connect one щуп a tester to the plug "B", and another – to each of rectifier plugs.
- Replace polarity щупов a tester and repeat item 1.
- Check that one shows conductivity existence, and another – is not present.
- If there is an electroconductivity, replace the rectifier.
|
|
1 — the plug "B"
2 — the rectifier plug |
|
|
Negative rectifier
|
|
- Using an ohmmeter, connect one щуп a tester to each of negative contacts, and another to each of rectifier plugs.
- Replace polarity щупов a tester and repeat item 1.
- Check that one shows conductivity existence, and another – is not present.
- If there is an electroconductivity, replace the rectifier.
|
|
1 — negative contact
2 — the rectifier plug |
|
|
Bearing
|
|
|
|
- Check that the drive and the bearing has no jags and are not worn-out.
|
|
|
- Check that the casing of the bearing has no jags and is not worn-out.
|
|
|
|
|
