Suzuki Grand Vitara SQ416/SQ420/420WD

since 1998 of release

Repair and car operation


Suzuki Grandee of Wetar
+ General information
+ Maintenance and greasing
+ Heater, ventilation and conditioner
+ Steering
+ Suspension bracket
+ Wheels and tires
+ Forward driving shaft/bearing of a shaft. Oil epiploon
+ Driveshafts
+ Brake system
+ Engines
+ Fuel system
+ ignition System
+ start System
+ release System
+ Transmissions
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. Immobilizer
- Electric equipment
   + body Electric equipment
   + lighting System
   - Electric equipment system
      + General description
      + Diagnostics
      + the Works made on the car
      - Major maintenance
         - Generator
            Removal
            Installation
            Dismantling [Type 60 A]
            Dismantling [Type 70 A and 80 A]
            Survey [Type 60 A]
            Survey [Type 70 A and 80 A]
            Replacement of brushes
            Assembly [Type 60 A]
            Assembly [Type 70 A and 80 A]
      + Specifications
      Inhaling moments
   + Tools/information for drivers

5917e1e5


Dismantling [Type 70 A and 80 A]

Type 70A

1 — a pulley nut
2 — a pulley
3 — a drive frame
4 — a stator
5 — a carving hairpin
6 — the drive bearing
7 — the holder of the bearing
8 — a rotor
9 — edge of a casing of the bearing

10 — a bearing cover
11 — a back frame
12 — the rectifier
13 — an insulator
14 — a regulator
15 — a brush
16 — a shchetkoderzhatel
17 — a back cover

Type 85 A

1 — a pulley nut
2 — a pulley
3 — a drive frame
4 — a stator
5 — a carving hairpin
6 — the drive bearing
7 — the holder of the bearing
8 — a rotor
9 — edge of a casing of the bearing
10 — a bearing cover
11 — a wavy washer

12 — a back frame
13 — a sealing cover
14 — the rectifier
15 — an insulator
16 — a regulator
17 — a brush
18 — a shchetkoderzhatel
19 — a cover of a shchetkoderzhatel
20 — a back cover
21 — a terminal guard


 PERFORMANCE ORDER

  1. Remove an internal nut of the plug "B" and an insulator.
  2. Remove a back cover.
1 — a back cover
2 — an insulator
3 — an internal nut of the plug "B"
  1. Remove 2 screws and extend assembly of a shchetkoderzhatel.
  2. Remove 3 screws and an IC regulator.
  3. Uncover a shchetkoderzhatel a shchetkoderzhatel.
1 — IC regulator screws
2 — an IC regulator
3 — screws of a shchetkoderzhatel
4 — assembly of a shchetkoderzhatel
  1. Remove 4 screws, 1 bolt and the rectifier.
1 — the rectifier
  1. Remove 4 rubber insulators (only type 80 A).
1 — a rubber insulator
  1. Holding a shaft a six-sided wrench, remove a pulley nut, and then extend a pulley.
  • For keeping of a shaft use a six-sided pulley. The Dvenadtsatigranny key can slide off and damage a shaft or the tool.
  • Do not try to hold a pulley flat-nose pliers or a trumpet key not to damage it.

1 — a pulley
2 — a six-sided key
3 — a cranked wrench
  1. Remove 4 nuts of a back frame.
  2. Beat out a back frame with a rotor, easily tapping on it with a plastic hammer.
  3. Carefully separate a back frame from a rotor, using a plastic hammer.

Do not strike on a shaft from a contact ring when divide a rotor and a back frame.


1 — a back frame
2 — a rotor shaft
3 — a nut of a back frame
  1. If necessary use a stripper for bearings to remove a casing of the bearing and a bearing cover.
  2. Be careful not to damage the blade of the cooling fan when using stripper.
1 — a bearing casing
2 — a bearing stripper
3 — a bearing cover
  1. If necessary remove 4 screws, a plate of the holder and then beat out the trailer bearing.
1 — a carving hairpin
2 — a holding plate
3 — the final bearing
4 — a stator
  1. If necessary, remove carving hairpins and extend a stator.

Will remove a stator easier if to warm up a frame.