Suzuki Grand Vitara SQ416/SQ420/420WD

since 1998 of release

Repair and car operation



Suzuki Grandee of Wetar
+ General information
+ Maintenance and greasing
+ Heater, ventilation and conditioner
+ Steering
+ Suspension bracket
+ Wheels and tires
+ Forward driving shaft/bearing of a shaft. Oil epiploon
+ Driveshafts
+ Brake system
+ Engines
+ Fuel system
+ ignition System
+ start System
+ release System
- Transmissions
   + Mechanical transmission (type 1)
   + Mechanical transmission (type 2)
   - Automatic transmission (4 A/T)
      + General description
      + Diagnostics of an automatic transmission
      + Precautionary measures at diagnostics of malfunctions
      + Visual survey
      - Service out of a workshop
         Liquid level
         Liquid replacement
         Hoses of a cooler of oil
         Cable of a throttle of an automatic transmission
         Manual selector
         Gear shifting cable
         Switch (sensor) of a range of transmission
         The sensor of speed on an exit of an automatic transmission
         Interruption switch on demand
         Solenoidal valves
         Switch of change of food \norm
         Tubes of a cooler of oil
      + System of blocking of brakes
      + system Check
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. Immobilizer
+ Electric equipment


5917e1e5



Solenoidal valves

Solenoidal valves of switching and solenoidal TCC valve

Check

Having disconnected hitches of the electronic control unit (RSM) and by means of a service wire, check each solenoidal valve on click existence.

G16/20 engines

1 — a service wire
2 — the disconnected sockets of the electronic control unit (RSM)

G16/20 engines

Solenoidal valve pereklyucheniya-A (No. 1)

С51 - 1-2

Solenoidal valve pereklyucheniya-V (No. 2)

С51 - 1-1

TSS solenoidal valve (blocking)

С51 - 1-8

Removal

 PERFORMANCE ORDER

  1. Take out oil щуп and lift the car.
  2. Let's to the engine cool down, remove a drain stopper from the pallet of a case and merge liquid of an automatic transmission.
  3. Establish a drain stopper with laying. Moment of an inhaling (a): 23 N • m (2.3 kg-m, 17.0 pounds foots).
  4. Remove an arm of an exhaust pipe and disconnect the forward driveshaft from forward differential (if is).
  5. Remove bolts of the pallet of a case.
  6. Remove the case pallet.
  7. Remove tubes for oil.
  8. Remove the solenoidal valve No. 1 (the solenoidal valve pereklyucheniya-A and In) or the solenoidal valve No. 2 (TSS solenoidal valve).
1 — a drain stopper
2 — the driveshaft

Work check

 PERFORMANCE ORDER

  1. Each time, removing solenoidal valves of switching and the TSS solenoidal valve (blocking) from a transmission, check their physical serviceability before installation into place.
  2. Put with a butterdish transmission liquid on the solenoidal valve and, having squeezed hands, check, that transmission liquid from a butterdish did not leave openings of the solenoidal valve when tension of the battery is not connected.
  3. Under the conditions described above connect tension of the battery and be convinced that liquid vigorously leaves.
  • If liquid does not leave vigorously at performance of the second point of check, do not use repeatedly this solenoidal valve.
  • In drawing check of the solenoidal valve of switching at the left is shown. Check the TSS solenoidal valve similarly.

Without tension of the battery

1 — a butterdish (with transmission liquid)
2 — the solenoidal valve
3 — the battery
And — an opening (should be dry)
In — let-out liquid

With tension of the battery

1 — a butterdish (with transmission liquid)
2 — the solenoidal valve
3 — the battery
And — an opening (should be dry)
In — let-out liquid

Installation

For installation of solenoidal valves execute removal procedure upside-down, paying attention to the following:

 PERFORMANCE ORDER

  1. Use new laying and About-shaped.......
  1. Establish tubes for oil in such sequence which is shown in drawing.
  1. Use new laying of the pallet of a case.
  2. Tighten universal flange bolts and nuts of the hinge and bolts of an arm of an exhaust pipe to the specified value of the moment of an inhaling.
  3. Fill in transmission liquid and check its level as it is described earlier in the Section liquid Replacement.
  4. After a warming up of an automatic transmission check, whether there is no leakage of liquid.