Suzuki Grand Vitara SQ416/SQ420/420WD

1. Remove a drum of a back brake. For more details see. Undressed the Brake drum (Removal) in Head the Parking and back brake.

2. Merge oil from the bridge case, having weakened a drain stopper.

3. Remove nuts (1) stopper of the bearing of a back wheel from the bridge case.

4. Remove the sensor of speed of a wheel (1) from the case of the back bridge (if there is a system of anti-blocking of brakes of ABS).

• At removal of the sensor of speed of a back wheel do not pull and excessively do not overwind a wire.
• Do not damage a surface of the sensor of speed of a back wheel or a rack and try, that the dust and dirt did not get to its adjusting opening.

5. Check that there is a gap between a stopper of the bearing of a back wheel (1) and the lever of a block of the parking brake (2). If the gap (3) is not present, weaken a cable lock-nut so that there was a gap.

6. By means of the special tool (B) and (C) pull out the bridge.
• Special tool:
• (C): 09943-35512
• (B): 09942-15510

Act carefully that together with bridge not to pull out a brake plate.

Pull out the bridge carefully not to hook on the top and bottom brake racks and a lay cable.

7. The pulled-out shaft of the back bridge.
   • Length of a shaft of "L":
     • left side: 711.5 mm (28.0 inches)
     • right side: 757.5 mm (29.8 inches)

8. If there is a system of anti-blocking of brakes of ABS to remove a sensor rotor from a lock ring, grind the grinding tool one part of a rotor of the sensor until it does not become thin.

9. Break a chisel an istonchenny part of a rotor of the sensor to remove it (if there is a system of anti-blocking of brakes of ABS).

10. To remove a lock ring (1) from a shaft (3), grind the grinding tool two parts (2) of a lock ring of the bearing (1) until they do not become thin.

Be not overzealous with polishing not to damage a shaft.

11. Break a chisel an istonchenny part of a lock ring to remove it.

12. Remove the bearing (2) from a shaft (1) by means of a hydraulic press (3).

14. By means of a hydraulic press (2) remove a hairpin (hairpins) (1).

The amount of the greasing put in a cavity of an oil epiploon, should take more than 60 % of its empty seat. “A”: greasing 99000-25010.

4. Establish a bearing (2) stopper on a shaft (1).

• Act carefully not to damage outer side of a lock ring.
• Establish the wheel bearing in the correct direction.

6. For the car with system of anti-blocking of brakes of ABS, establish by means of a press a new rotor of the sensor (1).

Act carefully not to damage outer side of a lock ring.

8. Put hermetic on an adjoining surface of a stopper of the bearing (1) with a brake plate.

Before drawing of new hermetic clear a surface of the old. “B”: hermetic 99000-31110.

9. Establish a shaft of the back bridge in the case of the bridge and tighten nuts of a stopper of the bearing to the specified value of the moment of an inhaling. Inhaling moment: nut of a stopper (a): 23 N • m (2.3 kg-m, 17.0 pounds foots).

At installation of the back bridge act carefully not to damage edge of an oil epiploon in the bridge case.

10. Tighten a bolt of the sensor of speed of a wheel to the specified value of the moment of an inhaling (if there is a system of anti-blocking of brakes of ABS). Inhaling moment: a bolt of the sensor of speed (b) — 21 N • m (2.1 kg-m, 15.5 pounds foots).