Suzuki Grand Vitara SQ416/SQ420/420WD

since 1998 of release

Repair and car operation


Suzuki Grandee of Wetar
+ General information
+ Maintenance and greasing
+ Heater, ventilation and conditioner
+ Steering
+ Suspension bracket
+ Wheels and tires
+ Forward driving shaft/bearing of a shaft. Oil epiploon
+ Driveshafts
+ Brake system
- Engines
   - Mechanical part of the G16 engine
      + General description
      - Routine maintenance
         Compression check
         Check of depression of the engine
         Check of pressure of oil
         Klapanny gap
         Filtering element of the air filter
         Cover of a head of cylinders
         Case of butterfly valves and inlet collector
         Collector of the fulfilled gases
         Belt of a drive of the gas-distributing mechanism and the tension device for a belt
         Oil pan and grid of the oil pump
         Oil pump
         Valve yoke, axis of yokes and cam-shaft
         Valves and head of the block of cylinders
      + piston Rod, piston rings, rods and cylinders
      Special tool
      Necessary service materials
      Technical characteristics of the rotating moment of an inhaling
   + Mechanical part of the J20 engine
   + engine Cooling
+ Fuel system
+ ignition System
+ start System
+ release System
+ Transmissions
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. Immobilizer
+ Electric equipment

5917e1e5


Collector of the fulfilled gases

Components

The car is not equipped warming three-componental with catalytic converter

1 — a collector of the fulfilled gases
2 — the top cover
3 — laying
4 — the sensor of heating of oxygen-1
5 — the bottom cover

6 — an element of rigidity of a collector of the fulfilled gases
7 — the adaptation for engine lifting at dismantle
8 — the coupling of the sensor of heating of oxygen-2

The car is equipped with warming three-componental catalytic converter

1 — a collector of the fulfilled gases
2 — the top cover
3 — laying
4 — the sensor of heating of oxygen-1
5 — the bottom cover

6 — an element of rigidity of a collector of the fulfilled gases
7 — the adaptation for engine lifting at dismantle
8 — the coupling of the sensor of heating of oxygen-2


The rotating moment of an inhaling.
Not to use repeatedly.

In order to avoid a burn, do not serve an exhaust system, if it still hot. Service should be carried out after the system will be cooled.

Dismantle

 PERFORMANCE ORDER

  1. Disconnect a negative cable from the accumulator.
  2. Disconnect the coupling of the sensor of heating of oxygen-1.
  3. Remove the top cover of a collector of exhaust gases.
  4. Remove bolts or nuts of an exhaust pipe and a bolt of an arm of an exhaust pipe (if that is available).
1 — an exhaust pipe No. 1
  1. Remove an element of rigidity of a collector of exhaust gases (3) (if that is available).
  1. Remove a collector of exhaust gases (1) and its laying (2) from a cylinder head.

Installation

 PERFORMANCE ORDER

  1. Put new laying (1) on a cylinder head.
  1. Establish a collector of exhaust gases and a rigidity element (if that is available).
  1. Attach condensing laying for connection of a pipe (1) and an exhaust pipe No. 1 (2) to a collector of exhaust gases (3). Before establishing condensing laying for connection of a pipe (1), check it about damage or wear, and if necessary replace. Use new lock-nuts if they are worn-out. Fasten pipe fixture to the specified rotating moment. The rotating moment of an inhaling: bolt or nut of an exhaust pipe No. 1 (and): 50 N • m (5.0 kg-m, 36.5 pounds on foot).
  1. Establish the top cover on a collector of exhaust gases.
  1. Connect the coupling of the sensor of heating of oxygen-1 (1) and insert the coupling into an arm (2), the 3rd adaptation for engine lifting at dismantle.
  1. Connect a negative cable to the accumulator. Check, whether there is no leakage of exhaust gas from an exhaust system.