Suzuki Grandee of Wetar
- General information
+ Precautionary measures
Main precautionary measures
Precautionary measures at work with the catalyst
Precautionary measures at service of electric chains
- Procedure of check of electric chains
Chain check on an open condition
Check on short circuit (short circuits on weight)
Interrupting or weak connection
Precautionary measures at installation of means of mobile communication
+ Identification information
Warning, warning and information stickers
Places of lifting of the car
The list of the reductions which are using in this management
+ Metric information
Standard moments of inhalings
+ Maintenance and greasing
+ Heater, ventilation and conditioner
+ Steering
+ Suspension bracket
+ Wheels and tires
+ Forward driving shaft/bearing of a shaft. Oil epiploon
+ Driveshafts
+ Brake system
+ Engines
+ Fuel system
+ ignition System
+ start System
+ release System
+ Transmissions
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. Immobilizer
+ Electric equipment
|
Chain check on an open condition Possible reasons of an open condition of a chain following: Quite often reason — in a konnektor or contacts, they should be in details checked.
- Leaky connection in a konnektor
- Weak contact on the plug (because of dirt, corrosion or a rust, hit of extraneous objects)
- Break in a plait of wires
At check, chains including electronic control units, such as ECM, TCM, ABS, is important to carry out careful check, since points which are easier for checking.
|
|
- Disconnect weight from the accumulator.
- Check each konnektor on both ends of a checked chain on weakening of connection. Also check a condition of fixing of the konnektor equipped with a clamp.
|
|
1 — check on existence of weak connections
2 — the sensor
3 — ECM |
- Using test covered contact, check both contacts of a checked chain on pressing of contacts of the covering plug. Check visually each plug on weakening of contacts (probably caused by pollution, corrosion, a rust, hit of extraneous objects etc.) As check, that contacts were densely latched in a konnektor.
|
|
1 — tension check in contacts by their connection and separation |
- By means of procedures of consecutive check or check of the electric tension, described on the following page, check electroconducting on break and weak connection of plugs. Find exact location of anomaly if it exists.
|
|
1 — weakened obzhaty
2 — a gap
3 — a thin wire |
|
|
Consecutive check
|
|
|
|
- Measure resistance between konnektor contacts on both ends of a checked chain (between A-1 and S-1 in drawing). If contiguity was not defined (infinity or limit excess), it means that the chain between plugs A-1 and S-1 is opened.
|
|
|
- Disconnect a konnektor included in a chain (a konnektor - In in drawing) and measure resistance between plugs A-1 and V-1. If contiguity was not defined, it means that the chain between plugs V-1 and S-1 is opened or there is an anomaly in a konnektor – Century.
|
|
|
Tension check
|
|
- If in a checked chain a food moves, check of tension can be used for chain check.
- With all attached konnektor and the tension submitted to a checked chain, measure tension between each plug and grounding.
- If measurements were carried out, and results were as on the list below, it means that the chain between plugs V-1 and A-1 is opened.
Tension between:
|
|
S-1 and weight — about 5 In
V-1 and weight — about 5
In A-1 and weight — 0 In |
- Also, if the measured values as on the list below, it means that there is a resistance (anomaly) at the level which is responsible for power failure in a chain between plugs A-1 and V-1.
Tension between:
|
|
S-1 and weight — about 5 In
V-1 and weight — about 5 In
A-1 and weight — 3 In (power failures 2 In) |
|
|
|
|
